My First Build
https://rotorbuilds.com/build/31971
fpvcustom - $31.95 - TBS Source One v5, 22xx-23xx FPV Motor Soft Mounts × 4 raceday quads - $80 - Flywoo GOKU GM10 Pro V3 GPS w/ Compass, Matek M10Q-5883 GNSS & Compass, M3 x 7mm Anti-Vibration Flight Controller Soft Mount Standoff 4 Pack, XT60 Pigtail 14AWG, Braided Mesh Wire Wrap, DIY Silicone Cable Set speedybee - $89.99 - SpeedyBee F7 V3 BL32 50A 30x30 Stack raceday quads - $242 - DJI O3 Air Unit Kit (w/ camera module & antennas) amazon - $111 - TBS Crossfire Nano Rx Pro, Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear ---- NEED MOTORS, BLADES, and BATTERIES, BATTERY CHARGER NEED CONTROLLER AND HEADSET DJI Goggles v2 - $250 DJI Goggles 2 DJI Controller - $250 OR TBS Tango 2 PRO FPV RC Radio Controller （new version） https://flywoo.net/products/tbs-tango-2-pro-fpv-rc-radio-controller?referral_code=7J0F3JHF50DI&slt=sales_plugin_af&source_type=sales_plugin_af ---- NOTES: alex vanover vanny style frame ---- Flywoo GOKU GM10 Pro V3 GPS w/ Compass https://www.racedayquads.com/products/flywoo-goku-gm10-pro-v3-gps-w-compass?variant=40122497597553 Matek M10Q-5883 GNSS & Compass https://www.racedayquads.com/products/matek-m10q-5883-gnss-compass?variant=40156958556273 TBS TRACER MICRO TX - FPV RACING DRONE TRANSMITTER https://www.team-blacksheep.com/products/prod:tbs_tracer_mtx ToolkitRC Q4AC 4x50w 4 Port AC DC Smart BATTERY Charger https://flywoo.net/products/new-toolkitrc-q4ac-4x50w-4-port-ac-dc-smart-charger?referral_code=7J0F3JHF50DI&sku=18057623928016113966722494&slt=sales_plugin_af&source_type=sales_plugin_af Rcinpower GTS V3 2105 Plus 1850KV/2950KV/3600KV M5-Mount Motor https://newbeedrone.com/products/rcinpower-gts-v3-2105-plus-1850kv-2950kv-3600kv-m5-mount-motor?variant=39506207277139 Do I still need to flash anything/do any configuration through BLHeli on my ESC? do I need to install wtf.fpv on my Goggles V2? I cannot seem to get GPS to stay connected, and I cannot figure out the LED setup either.
I could really use some guidance on setting up my first 5inch drone in betaflight (DJI 03 air unit), and then also how to setup my goggles v2 and TBS tango controller as well. I just recently got into building an FPV drone after getting sucked into the YouTube rabbit hole. I already had experience with 3D printing, software development, soldering, board level repair, reading scematics, etc therefore picking up the hobby made sense. I've been watching Josh Bardwell's videos on how to use betaflight but I seem to have accidentally deleted the backup config that came from the Speedybee factory. So far I have confirmed that the motors work and that they spin the correct direction. I'm not sure what UART goes to which port on the ports tab of betaflight (v4.4.3). Attached image is straight from the speedybee page for the FC, and exactly how I have it wired. Any help or advise would be greatly appreciated, thanks in advance. FRAME - TBS Source One v5 ESC and FC (stack) - SpeedyBee F7 V3 BL32 50A 30x30 Stack VTX - DJI O3 Air Unit (SBUS wire removed in favor of the Crossfire Nano RX) RX - TBS Crossfire Nano RX Pro, w/ antenna Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear Goggles - DJI Goggles V2 Controller - TBS Tango 2 Batteries - RDQ Series 22.2V 6S 1300mAh 100C LiPo Battery - XT60 GPS - Flywoo GOKU GM10 Pro V3 GPS w/ Compass Rotorbuild link: https://rotorbuilds.com/build/31971