Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| personal:drones:my-first-build [2024/05/28 22:03] – jimboobrien | personal:drones:my-first-build [2024/05/29 04:37] (current) – jimboobrien | ||
|---|---|---|---|
| Line 73: | Line 73: | ||
| https:// | https:// | ||
| - | </ | ||
| - | < | ||
| - | hello Reddit, | ||
| - | this is one of my first posts, I just recently got into building FPV drones after getting sucked into the YouTube rabbit hole. | ||
| - | I already had experience with 3D printing, software development, | ||
| - | I planned a 5inch drone with the following parts: | ||
| - | Frame - TBS Source One v5 | ||
| - | Stack - SpeedyBee F7 V3 BL32 50A 30x30 Stack | ||
| - | Video TX - DJI O3 Air Unit Kit (w/ camera module & antennas) | ||
| - | RX - TBS Crossfire Nano Rx Pro, Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear | ||
| + | Do I still need to flash anything/do any configuration through BLHeli on my ESC? | ||
| - | Motors - iFlight 4pcs XING-E Pro 2207 1800KV Brushless Motor 6S | ||
| - | Props - Azure Power Johnny Freestyle 4.8x3.8x3 POPO Compatible Tri-Blade 5" | ||
| + | do I need to install wtf.fpv on my Goggles V2? | ||
| - | Goggles - DJI Goggles V2 | ||
| - | Controller - TBS Tango 2 | ||
| - | Batteries - RDQ Series 22.2V 6S 1300mAh 100C LiPo Battery - XT60 | + | I cannot seem to get GPS to stay connected, and I cannot figure out the LED setup either. |
| - | GPS - Flywoo GOKU GM10 Pro V3 GPS w/ Compass | ||
| Line 106: | Line 93: | ||
| - | My Build on Rotosbuilds, | ||
| - | https:// | ||
| + | </ | ||
| + | < | ||
| + | I could really use some guidance on setting up my first 5inch drone in betaflight (DJI 03 air unit), and then also how to setup my goggles v2 and TBS tango controller as well. | ||
| + | |||
| + | I just recently got into building an FPV drone after getting sucked into the YouTube rabbit hole. I already had experience with 3D printing, software development, | ||
| + | |||
| + | I've been watching Josh Bardwell' | ||
| + | |||
| + | So far I have confirmed that the motors work and that they spin the correct direction. I'm not sure what UART goes to which port on the ports tab of betaflight (v4.4.3). | ||
| + | |||
| + | Attached image is straight from the speedybee page for the FC, and exactly how I have it wired. Any help or advise would be greatly appreciated, | ||
| + | |||
| + | FRAME - TBS Source One v5 | ||
| + | ESC and FC (stack) - SpeedyBee F7 V3 BL32 50A 30x30 Stack | ||
| + | VTX - DJI O3 Air Unit (SBUS wire removed in favor of the Crossfire Nano RX) | ||
| + | RX - TBS Crossfire Nano RX Pro, w/ antenna Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear | ||
| + | Goggles - DJI Goggles V2 | ||
| + | Controller - TBS Tango 2 | ||
| + | Batteries - RDQ Series 22.2V 6S 1300mAh 100C LiPo Battery - XT60 | ||
| + | GPS - Flywoo GOKU GM10 Pro V3 GPS w/ Compass | ||
| - | 4 x RCINPOWER GTS V3 0802 22000KV Brushless FPV Drone Motor - Choose Color (4 builds) | + | Rotorbuild link: https:// |
| </ | </ | ||