Differences

This shows you the differences between two versions of the page.

--- personal:drones:my-first-build [2023/12/30 05:46] – jimboobrien
+++ personal:drones:my-first-build [2024/05/29 04:37] (current) – jimboobrien
@@ Line 1: / Line 1: @@
 ====== My First Build ======
+https://rotorbuilds.com/build/31971
 <code>
-TBS Source One V5 - 23.99
-mm wide camera dji o3
-alex vanover vanny style frame
-xx-23xx FPV Motor Soft Mounts × 4 - 6.99
+fpvcustom - $31.95 - TBS Source One v5, 22xx-23xx FPV Motor Soft Mounts × 4
+raceday quads - $80 - Flywoo GOKU GM10 Pro V3 GPS w/ Compass, Matek M10Q-5883 GNSS & Compass, M3 x 7mm Anti-Vibration Flight Controller Soft Mount Standoff 4 Pack, XT60 Pigtail 14AWG, Braided Mesh Wire Wrap, DIY Silicone Cable Set
+speedybee - $89.99 - SpeedyBee F7 V3 BL32 50A 30x30 Stack
-DJI 03 air unit - 279.99
+raceday quads - $242 - DJI O3 Air Unit Kit (w/ camera module & antennas)
+amazon - $111 - TBS Crossfire Nano Rx Pro, Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear
+----
+NEED MOTORS, BLADES, and BATTERIES, BATTERY CHARGER
+NEED CONTROLLER AND HEADSET
@@ Line 23: / Line 36: @@
 TBS Tango 2 PRO FPV RC Radio Controller （new version）
 https://flywoo.net/products/tbs-tango-2-pro-fpv-rc-radio-controller?referral_code=7J0F3JHF50DI&slt=sales_plugin_af&source_type=sales_plugin_af
+----
+NOTES:
+alex vanover vanny style frame
+----
+Flywoo GOKU GM10 Pro V3 GPS w/ Compass
+https://www.racedayquads.com/products/flywoo-goku-gm10-pro-v3-gps-w-compass?variant=40122497597553
@@ Line 39: / Line 68: @@
-Flywoo GOKU GM10 Pro V3 GPS w/ Compass
-https://www.racedayquads.com/products/flywoo-goku-gm10-pro-v3-gps-w-compass?variant=40122497597553
 Rcinpower GTS V3 2105 Plus 1850KV/2950KV/3600KV M5-Mount Motor
 https://newbeedrone.com/products/rcinpower-gts-v3-2105-plus-1850kv-2950kv-3600kv-m5-mount-motor?variant=39506207277139
+Do I still need to flash anything/do any configuration through BLHeli on my ESC?
+do I need to install wtf.fpv on my Goggles V2?
+I cannot seem to get GPS to stay connected, and I cannot figure out the LED setup either.
+</code>
+<code>
+I could really use some guidance on setting up my first 5inch drone in betaflight (DJI 03 air unit), and then also how to setup my goggles v2 and TBS tango controller as well.
+I just recently got into building an FPV drone after getting sucked into the YouTube rabbit hole. I already had experience with 3D printing, software development, soldering, board level repair, reading scematics, etc therefore picking up the hobby made sense.
+I've been watching Josh Bardwell's videos on how to use betaflight but I seem to have accidentally deleted the backup config that came from the Speedybee factory.
+So far I have confirmed that the motors work and that they spin the correct direction. I'm not sure what UART goes to which port on the ports tab of betaflight (v4.4.3).
+Attached image is straight from the speedybee page for the FC, and exactly how I have it wired. Any help or advise would be greatly appreciated, thanks in advance.
+FRAME - TBS Source One v5
+ESC and FC (stack) - SpeedyBee F7 V3 BL32 50A 30x30 Stack
+VTX - DJI O3 Air Unit (SBUS wire removed in favor of the Crossfire Nano RX)
+RX - TBS Crossfire Nano RX Pro, w/ antenna Team Blacksheep TBS Crossfire Immortal T Antenna V2 - Extra Extended - Linear
+Goggles - DJI Goggles V2
+Controller - TBS Tango 2
+Batteries - RDQ Series 22.2V 6S 1300mAh 100C LiPo Battery - XT60
+GPS - Flywoo GOKU GM10 Pro V3 GPS w/ Compass
+Rotorbuild link: https://rotorbuilds.com/build/31971
 </code>